U型玻璃是采用特殊工艺加工而成的新型建筑墙體材料，具有不可燃烧的特性。U型玻璃可用于建筑内墙、外墙、隔断等位置，如若用于外墙常用于多层建筑，玻璃所使用的高度取决于项目当地的风荷载、距离地面高度、玻璃连接方式等。

U-shaped glass is a new type of building wall material which is processed by special technology and has the characteristic of non-combustible. U-shaped glass can be used for internal walls, external walls, partitions and other positions. If it is used for external walls, it is often used for multi-storey buildings. The height of glass used depends on the local wind load of the project, the height from the ground, the connection mode of glass and so on.

U型玻璃

U型玻璃玻璃可采用单层、多层安装方式，是否预留通风缝可根据设计图而定。U型玻璃可采用铝型材（常见方式）、不锈钢边框、黑色金属材料等作為包边，同时金属材料要做好相应的防腐防锈处理。U型玻璃的生产安装可参考以下图集和标准：

建筑材行业标准JC/T 867-2000《建筑用U形玻璃》

德國工业标准DIN1055和DIN1249

國家建筑标准设计图集06J505-1《外装修(一)》

U型玻璃不同尺寸规格参数：

U-shaped glass can be installed in single or multiple layers. Whether ventilation joints are reserved can be determined according to the design drawing. U-shaped glass can be aluminum (common), stainless steel frame, black metal materials as the edge, while the metal materials to do the corresponding anti-corrosion and anti-rust treatment. The production and installation of u-shaped glass can refer to the following atlas and standards:
Building material industry standard JC/T 867-2000 "u-shaped glass for building"
German industrial standard DIN1055 and DIN1249
National building standard design atlas 06j505-1 "exterior decoration (I)"
Specification parameters of different sizes of u-shaped glass:

建筑U型玻璃安装要求：

1、固定型材：将铝型材或其他金属型材用不锈钢螺栓或铆钉固定在建筑上，边框材料与墙面或建筑洞口牢固固定，每延米应不低于2个固定点。

Installation requirements for u-shaped glass in buildings:
1, fixed profiles: aluminum profiles or other metal profiles with stainless steel bolts or rivets fixed in the building, frame material and the wall or the building hole fixed firmly, each meter should not be less than 2 fixed points.

U型玻璃隔断设计

2、玻璃入框架：将U型玻璃内面洗净，镶入框架，将起缓冲作用的塑料件截成相应長度放入固定框架内。

3、U型玻璃安装到最后三块时，先将两块玻璃放入边框，再用第三块玻璃封扣；如果剩余洞口宽度余量不能装入整块玻璃时，可将U型玻璃沿着長度方向裁切来满足剩余宽度，裁切后的玻璃应该先行安装。

4、对于温差加大的地區，U型玻璃之间的间隙应根据温度进行伸缩调整；

2. Glass into the frame: wash the inner surface of the u-shaped glass and insert it into the frame. Cut the plastic parts with buffer function into corresponding lengths and put them into the fixed frame.
3. When the u-shaped glass is installed to the last three pieces, first put the two pieces of glass into the frame, and then seal the buckle with the third piece of glass; If the remaining width of the hole cannot fit into the whole glass, the u-shaped glass can be cut along the length to meet the remaining width, and the cut glass should be installed first.
4. For regions where the temperature difference increases, the gap between u-shaped glasses should be adjusted according to the temperature;

U型玻璃隔断设计

5、U型玻璃水平宽度大于2m时，横向构件水平度可允许3mm偏差；当高度不大于5m时，边框垂直度允许5mm偏差；高度不大于6m时，构件跨向挠度允许8mm偏差；

6、边框与U型玻璃之间用弹性垫条填充缝隙，垫条与玻璃和边框接触面不少于12mm;

7、在边框与玻璃，玻璃与玻璃，边框与建筑结构體存在的接缝采用玻璃胶类弹性密封材料(或硅酮胶密封)进行填充；

5. When the horizontal width of u-shaped glass is more than 2m, the horizontal degree of transverse members can be allowed to have a deviation of 3mm; When the height is no more than 5m, the verticality of the border is allowed to have a deviation of 5mm. When the height is not more than 6m, the member's cross-deflection is allowed to be 8mm deviation;
6. Fill the gaps between the frame and the u-shaped glass with elastic strip, and the contact surface between the strip and the glass and the frame shall be no less than 12mm;
7. The joints between the frame and the glass, the glass and the glass, the frame and the building structure are filled with the elastic sealing material of glass glue (or silicone rubber seal);

U型玻璃外墙设计

8、U形玻璃建筑墙體时非承重墙，不可受力，边框承受的荷载力应传给建筑物；

9、U型玻璃及边框安装完工后，玻璃内外表面擦拭干净，清洁场地遗留的物品。

8, u-shaped glass building wall is not load-bearing wall, can not bear the force, the frame load should be transmitted to the building;
9. After the installation of u-shaped glass and its frame, the inner and outer surfaces of the glass shall be wiped clean to clean the articles left behind in the site.